Cooling Tower Chemical

ChemWorld 1334 is a cooling water chemical product is used to minimize corrosion and to prevent scaling.

ChemWorld 1334 is a treatment program designed for recirculating cooling water systems operating at moderately scaling conditions. The product contains a combination of phosphonates, polymeric dispersants, and azole specifically formulated to minimize scale, general deposition, and corrosion under moderate operating conditions. This product:

• Controls deposition and scale.
• Reduces water and treatment cost by enabling higher cycle operation.
• Operation at higher pH allows for minimum or no acid feed.
• Federate is 400 to 1200 ppm. Maintain between 10 to 15 ppm of organophosphonate in the water.
• Monitor organophosphonate residuals with a organophosphonate test kit and a hand held conductivity controller.
• Use rate is 4 to 12 gallons per 10,000 gallons of fresh makeup water.

ChemWorld 1334 is a mixture of the below chemicals:

• Potassium Hydroxide (Cas No.1310-58-3)
• Aminotri(Methylenephosphonic Acid) Potassium Salt (Cas No. 27794-93-0)
• Hydroxyethylidene Diphosphonic Acid, Potassium Salt (Cas No. 67953-76-8)
• Carboxylated Acrylic Polymer, Sodium Salt (Cas No. PROPRIETARY)
• Sodium Tolytriazole (Cas No. 64665-57-2)

For new cooling tower startups, consider our ChemWorld 101 Cooling Startup Kit. This kit includes the following:

• One 5 gallon pail of ChemWorld Q-ALK-PC - This product is required to clean the debris and greases prior to startup.
• One 5 gallon pail of ChemWorld 1334 - ChemWorld 1334 is scale and corrosion control cooling tower chemical. After startup you can perform testing of your water hardness and alkalinity and we can tune in your exact chemical for long term protection.
• One 5 gallon pail of ChemWorld 56 - ChemWorld 56 is a 12.5% sodium hypochlorite product that is required to kill bacteria. This is the cheapest easiest product to get your system up and going, you can convert to tablets or a stablized bromide product after startup.
• One LakeWood 140 Cooling Tower Controller - You will need to set the controller to feed and bleed the cooling tower water to maximize cycles and to minimize chemical usage rates. An optional dual biocide water treatment can be implemented after startup. This is model 1239597 (which is board mounted unit that has the flow assembly on the left).
• One 1167435 Cooling Tower Blowdown Valve (1" NPT) - This will be required when the cooling tower calls to release cooling tower water.
• Two Stenner 45MHP10 Adjustable Head Pumps - One pump is required for the corrosion/ scale prevention chemical and for the biocide. Each pump is rated to 100 psi, which should be enough to feed the chemical into the system. The ideal spot to feed the chemical is into the return header of the cooling tower. These Stenner Pump kits come with chemical injection valves that will allow for quick injection of each chemical into the side stream water loop that is used to monitor the cooling tower conductivity.
• One complete CWTK-200 Cooling Water Treatment Test Kit. This kit is contains every test you will need to set up and fine tune your water treatment program.
• One Chemical Metal Test Station Cabinet - You need to keep your test kits and lo sheets in one clean location. This test kit is ideal for cooling towers. Items in the photo of test kit not included.

We have a cooling tower system that is a split system with a heat exchanger . So I am looking for some advice on which product to use. The closed part of the system circulates water through our molds for heating and cooling temps up to around 450deg. The molds are aluminum and steel. So I am looking for corrosion protection and I also need an algae preventer.
On the outside part of the system I need corrosion , scale and algae protection as well. The outside has a high evaporation while the inside loop has little evaporation.
On the open loop side you want to use a corrrosion/scale prevention chemical like our Chemworld 1334.
On the closed loop side you should use our 2338D corrosion inhibitor.
Bromax 7.1 would be the best biocide for your application.